What have you done for your T7 today?

[bth2]

On 4/8/2020 at 6:09 PM, X Plane said:

Pictures pictures 

how many do you need  

photos of white exhaust cover

[Noel McCutcheon]

Thanks, guess just the one be enough, lol.
The white kind of goes with your bike I’ll say.

Dam that dam Boredom, maybe not for everyone’s cup of tea I guess .

Different, you can always redo if selling or trading her .

[Gezgin Endurocu]

For city use ı put 50 liter aluminium top case it is made in Turkey...

[Noel McCutcheon]

^ Handy ^ Fill it and Front wheel should lift easier .

[Lupo]

Homemade tail tidy made from the original one 

[Great Escape]

On 2/1/2020 at 4:55 PM, Rich TT said:

Top man. Looks ace. Cracking job

Hi, did you fit the foam grips over the heated grips...?  Cheers,  Steve 

[bth2]

On 4/12/2020 at 10:22 AM, X Plane said:

Thanks, guess just the one be enough, lol.
The white kind of goes with your bike I’ll say.

Dam that dam Boredom, maybe not for everyone’s cup of tea I guess .

Different, you can always redo if selling or trading her .

yes ,its a little sad ,i know.....but needs must....i may even re-spray silver

 

[Great Escape]

Changed my 'short ' clutch lever to a longer version of the same,  the short brake lever is comfy to use but the short clutch lever is not,  your fingers pull against the balled end .  Cheers,  Steve 

[MichelP]

MIVV end can, and removed rear footpegs.

[Lupan]

Nice Look. One of the reasons i didn´t bought that exhaust was the red traces in the Mivv plate eheheh

But in the White and Red T7 looks very good

Edited April 15, 2020 by Lupan

[Allen Kelly]

What do I do now??????????????

Fitted the B&B off Road Engineering (Aus.) bash plate and the Adventure Spec crash bar (the only thing I couldn’t get manufactured in Australia). Fitted the pannier packs on and I’m ready to go except for the lock down. Now that that’s all done I don’t know what else to do. I just want to ride the bloody thing now.

[shaneygrog]

25 minutes ago, Allen Kelly said:

..........Now that that’s all done I don’t know what else to do.....

 

 

 

That looks real nice Allen.

 

I got an idea for you though, to keep you busy. Pull the bike apart, right down to the last piece, get some new gaskets and then put it all back together. By the time you have done that we should all be allowed out again? 

[al700]

Maybe add a high fender kit...to look like a proper Rally bike.

[manny]

4 hours ago, Allen Kelly said:

What do I do now??????????????

Fitted the B&B off Road Engineering (Aus.) bash plate and the Adventure Spec crash bar (the only thing I couldn’t get manufactured in Australia). Fitted the pannier packs on and I’m ready to go except for the lock down. Now that that’s all done I don’t know what else to do. I just want to ride the bloody thing now.

I see your still holding onto the xt, whats your comparison between the 2 ?

[tenerecanada]

5 hours ago, Allen Kelly said:

What do I do now??????????????

Fitted the B&B off Road Engineering (Aus.) bash plate and the Adventure Spec crash bar (the only thing I couldn’t get manufactured in Australia). Fitted the pannier packs on and I’m ready to go except for the lock down. Now that that’s all done I don’t know what else to do. I just want to ride the bloody thing now.

Really nice setup Allen. Great choice in parts.

[Davey]

Finally got round to fitting rally pro grips and Cycra pro bends, love em !

 

[Allen Kelly]

10 hours ago, manny said:

I see your still holding onto the xt, whats your comparison between the 2 ?

Chalk and cheese. I took the XT out for a short run a couple of days ago to get the oil circulating it was like going from a Rolls Royce to a Sherman tank. The XT is such a raw bike in every sense of the word especially on road. I have actually just sold it to a mate because I can’t see me on it much now with the T700

[Noel McCutcheon]

3 hours ago, Davey said:

Finally got round to fitting rally pro grips and Cycra pro bends, love em !

 

 

 

Good work and nice job Davy.  
 

The wind defection / protection looks good with those hand guards. 
 

[tenerecanada]

6 hours ago, Davey said:

Finally got round to fitting rally pro grips and Cycra pro bends, love em !

 

Thanks for the post Davey. I have a pair of these in my pile of dusty mods ready to go on the Tenere when it shows up, and have been curious how tight it will be around the levers. Cheers. 

[manny]

13 hours ago, Allen Kelly said:

Chalk and cheese. I took the XT out for a short run a couple of days ago to get the oil circulating it was like going from a Rolls Royce to a Sherman tank. The XT is such a raw bike in every sense of the word especially on road. I have actually just sold it to a mate because I can’t see me on it much now with the T700

yeah I have had 3 xt600s over the years & did lots of klms on them but the t7 kills it, its so much smoother & has no chain snatch. the only thing the 600 had better was the less weight

[Davey]

14 hours ago, tenerecanada said:

Thanks for the post Davey. I have a pair of these in my pile of dusty mods ready to go on the Tenere when it shows up, and have been curious how tight it will be around the levers. Cheers. 

Levers are a bit tight depending on angle of bars and such, looking at some short levers as use to using two fingers anyway but the standard ones work okay.

[Davey]

17 hours ago, X Plane said:

The wind defection / protection looks good with those hand guards. 
 

Thanks, just wanted something other than Barkbusters and these seem really good, and without paying for extra addons it's all there in the pack !

Edited April 17, 2020 by Davey
Spelling

[Duncan666]

I took it for a ride, it was my commute.  

 

 

Edited April 17, 2020 by Duncan666

[Murska]

Diy progressive 1/5 throttle tube.

 

[boboneleg]

On 4/15/2020 at 10:59 AM, MichelP said:

MIVV end can, and removed rear footpegs.

 

On 4/15/2020 at 10:59 AM, MichelP said:

MIVV end can, and removed rear footpegs.

 

I removed my rear pegs as well, do yourself a favour and blank the holes off with something like these or you might get water ingress in the frame.

 

https://www.ebay.co.uk/itm/M5-M6-M8-M10-FLANGED-HEX-HEAD-BOLTS-FLANGE-SCREWS-A2-STAINLESS-STEEL-BOLT/323358421026?ssPageName=STRK%3AMEBIDX%3AIT&var=512419597469&_trksid=p2057872.m2749.l2649

Edited April 18, 2020 by boboneleg